Impact of photoinitiator quality on chemical-mechanical properties of dental adhesives under different light intensities / Impacto da qualidade de fotoiniciadores nas propriedades químico mecânicas de adesivos dentais sob diferentes intensidades de luz

Objective: Evaluate the mechanical properties of experimental adhesive models with different photoinitiators (PI) polymerized by LED units of different power densities. Material and Methods: Three groups of adhesive models based on HEMA/BisGMA (45/55) were prepared in association with different PI combinations: G2 (control) ­ 2 PI: 0.5% CQ, 0.5% EDMAB; G3 - 3 PI: 0.5% CQ; 0.5% DMAEMA, 0.5% DPIHP; G4 - 4 PI: 0.5% CQ; 0.5% EDMAB; 0.5% DMAEMA; 0.5% DPIHP. The three formulations were polymerized at two different LED power densities: 550 mW/cm2 and 1200 mW/cm2. The degree of conversion (DC) of adhesive monomers was monitored in situ through the FTIR for 600 s. Specimens were prepared for each formulation for analysis mong adhesive systems (G2

Objetivo: Avaliar as propriedades mecânicas de modelos adesivos experimentais com diferentes fotoiniciadores (PI) polimerizados por unidades de LED de diferentes densidades de energia. Material e Métodos: Três grupos de modelos adesivos baseados em HEMA/BisGMA (45/55) foram preparados em associação com diferentes combinações de PI: G2 (controle) ­ 2 PI: 0,5% CQ, 0,5% EDMAB; G3 - 3PI: 0,5% CQ; 0,5% DMAEMA, 0,5% DPIHP; G4 - 4 PI: 0,5% CQ; 0,5% EDMAB; 0,5% DMAEMA; 0,5% DPIHP. As três formulações foram polimerizadas em duas densidades de potência de LED: 550 mW/cm2 e 1200 mW/cm2. O grau de conversão (DC) dos monômeros adesivos foi monitorado in situ através do FTIR durante 600 s. Amostras foram preparadas para cada formulação para análise de resistência à flexão (FS), módulo de elasticidade (ME), sorção (SOR) e solubilidade (SOL). Os dados foram submetidos aos testes ANOVA 2-fatores e Tukey (5%). Resultados: DC: houve diferença significativa entre os sistemas adesivos (G2

Effect of Light-Curing Unit Type and Bulk-Fill Composite Resins with Different Photoinitiators on Marginal Gaps of Class II Restorations

Abstract Objective: To evaluate the effect of two types of light-curing units (second and third generations) and two types of bulk-fill composite resins with different photoinitiators - Tetric N-Ceram Bulk Fill (TNCB) and Xtra Fil (XTF) on gap formation at the gingival margins of Cl II restorations. Material and Methods: Fifty-six standard Cl II cavities were prepared on the mesial and distal surfaces of premolar teeth, with the gingival margin of the cavities 1 mm apical to the CEJ. The samples were randomly assigned to two groups based on the composite resin type and two subgroups based on the light-curing unit type and restored. After 5000 rounds of thermocycling, gingival margin gap in each sample was measured in µm under an electron microscope at ×2000 magnification. Data were analyzed by two-way ANOVA and Tukey tests (α=0.05). Results: Marginal gaps of TNCB composite resin were significantly smaller than those of XTF composite resin (p<0.001). There were no significant differences between the two light-curing units in each group (p=0.887 with XTF and p=0.999 with TNCB). Conclusion: The gaps at gingival margins of Cl II cavities with TNCB bulk-fill composite were smaller than XTF composite resin. Both composite resins can be cured with both the second- and third-generation LEDs (AU).

Influence of customization and light-curing device on the bond strength of glass fiber posts - in vitro study / Influência da reanatomização e do aparelho fotopolimerizador na resistência de união de pinos de fibra de vidro - estudo in vitro

Introduction: Endodontically treated teeth are usually affected by extensive structure loss requiring the use of intraradicular posts to provide retention and restoration. Objective: An in vitro assessment was performed on the bonding of glass fiber posts to the root dentin. Material and method: Ninety (n = 10) single bovine roots were used in a 3 x 3 x 3 factorial study with subdivided plots: post customization varying the presence and type of resin (without customization, conventional resin, and Bulk Fill resin), light-curing device (Valo, Radii-Cal, Rainbow), and root third (cervical, middle, and apical). Result: For the customization factor, Tukey's test (5%) showed the superiority of the Bulk Fill (8.16 MPa) and Z350 (7.40 MPa) groups compared to the control group (4.92 MPa), without differing from each other. All light-curing devices differed, showing the superiority of Valo (9.36 MPa), Radii (6.96 MPa) as an intermediate, and the inferiority of Rainbow (4.17 MPa). The cervical root third (7.81 MPa) was superior, the apical third was inferior (5.80 MPa), and the middle third (6.88 MPa) was an intermediate without differing from the others. Conclusion: The customization of glass fiber posts increases the bond strength to the root dentin, regardless of the resin used. There was a compromise in the apical third and when using light-curing devices with lower light intensity.

Introdução: Dentes com extensa perda de estrutura podem comprometer a retenção das restaurações ao remanescente dental, onde pinos intraradiculares são indicados. Objetivo: Avaliou-se in vitro a união de pinos de fibra de vidro à dentina radicular em função de diferentes modos de reanatomização, fotopolimerizadores e regionalização radicular. Material e método: Noventa (n=10) raízes bovinas uniradiculares foram usadas num estudo fatorial 3 x 3 x 3 com parcelas subdivididas: Reanatomização do pino, variando a presença e tipo de resina (Sem reanatomização, Resina Convencional e Resina Bulkfill); Fotopolimerizador (Valo, Radii-cal, Rainbow); e Terço radicular (cervical, médio e apical). Resultado: O teste de Tukey (5%) evidenciou para o Fator Reanatomização superioridade dos grupos BulkFill (8.16MPa) e Z350 (7.40MPa) ao grupo Controle (4.92MPa), sem diferirem entre si. Todos os fotopolimerizadores diferiram entre si, com superioridade de Valo (9.36MPa), Radii (6.96MPa) intermediário, e inferioridade de Raiwbow (4.17MPa). O terço radicular cervical (7.81MPa) foi superior e o apical inferior (5.80MPa), com o terço médio (6.88MPa) intermediário e sem diferir dos demais. Conclusão: Conclui-se que a reanatomização de pinos de fibra de vidro aumenta a resistência de união à dentina radicular, independentemente da resina utilizada, havendo prejuízo no terço apical e quando são empregados fotopolimerizadores com menor intensidade luminosa.

Effect of MDP concentration and addition of iodonium salt on the dentin bond strength of experimental adhesives / Efeito da concentração de MDP e adição de sal de iodônio na resistência de união à dentina de adesivos experimentais

Objetivo: O objetivo foi avaliar a resistência de união de seis adesivos experimentais contendo sistemas fotoiniciadores binários ou ternários, associados a três diferentes concentrações de MDP (0-12% em peso) após 12 meses de armazenamento em água destilada. Material e Métodos: Adesivos experimentais foram preparados com: bis-GMA, UDMA, bis-EMA, TEGDMA, HEMA, BHT e etanol, contendo sistemas fotoiniciadores binários (CQ/amina) ou ternários (CQ/amina/DPIHFP ­ 0,5% em peso). Foi adicionado a esta composição 0%, 6% ou 12% em peso de MDP. Os sistemas adesivos foram aplicados seguindo o protocolo com condicionamento ácido. Moldes cilíndricos transparentes foram colocados sobre a dentina hibridizada, preenchidos com resina composta e fotopolimerizados. Os corpos-de-prova foram armazenados em água destilada a 37oC por 24h ou 12 meses e submetidos ao ensaio de microcisalhamento (n=6). Os dados foram analisados por ANOVA de três fatores e teste de Tukey (α=5%). Resultados: Para o sistema binário, após 12 meses de armazenamento, todos os valores de resistência de união foram semelhantes. Em relação à degradação da resistência de adesão ao longo do tempo, as formulações de MDP de 6% e 12% mostraram resistência de união mais estável do que 0% de MDP. Para o sistema ternário, todas as formulações (0%, 6% e 12% em massa de MDP) mostraram resistência de união estável em função do tempo. Conclusão: Para o sistema binário, as concentrações de 6 e 12% em massa de MDP foram capazes de manter a resistência de união em função do tempo, enquanto que para o sistema ternário, a estabilidade de união foi obtida independentemente da concentração de MDP. Pode-se concluir que, para a formulação dos adesivos utilizados neste estudo, independente do sistema fotoiniciador, a concentração de 12% MDP apresentou valores de resistência de união mais estáveis após 12 meses de armazenamento em água (AU)

Objective: The aim was to evaluate the bond strength of six experimental adhesives containing binary or ternary photoinitiator systems, associated with three different MDP concentrations (0-12wt%) after 12 months of storage in distilled water. Material and Methods: Experimental adhesives were prepared with: bis-GMA, UDMA, bis-EMA, TEGDMA, HEMA, BHT, and ethanol, containing binary (CQ/amine) or ternary (CQ/amine/DPIHFP (diphenyliodonium hexafluorophosphate) ­ 0.5wt%) photoinitiator systems. It was added to this composition 0wt%, 6wt%, or 12wt% of MDP. The adhesive systems were applied following the etch-and-rinse protocol. Transparent cylindrical molds were placed on the hybridized dentin, filled with composite resin and light-cured. The specimens were stored in distilled water at 37oC for 24h or 12 months and submitted to a microshear bond strength test (n=6). Data were analyzed by three-way ANOVA and Tukey's test (α=5%). Results: For the binary system, after 12 months of storage, all bond strength values were similar. Regarding bond strength degradation over time, 6wt% and 12wt% MDP formulations showed more stable bond strength than 0wt% MDP. For the ternary system, all formulations (0wt%, 6wt% and 12wt%) showed stable bond strength over time. Conclusion: For the binary photoinitiator system, the 6wt% and 12wt% MDP concentrations were able to keep bond strength stable over time, while for the ternary system, bond strength stability was achieved regardless the MDP concentration. (AU)

Effect of combining photoinitiators on cure efficiency of dental resin-based composites

Abstract Camphorquinone is the most conventionally used photoinitiator in Dentistry. Although different alternative photoinitiators have been proposed, no photoinitiator was capable of completely substituting camphorquinone. The combination of photoinitiators has been considered the best alternative. Objectives: To evaluate the effect of combining Norrish type I and II photoinitiators on the cure efficiency of dental resin-based composites. Methodology: Experimental composites were produced containing different photoinitiator systems: Norrish type I-only, mono-alkyl phosphine oxide (TPO); Norrish type II-only, camphorquinone (CQ); or its combination, CQ and TPO, in a 1: 1 molar ratio. UV-vis absorption spectrophotometry was performed to assess the consumption of each photoinitiator after curing (n=3). A multi-wave LED (Bluephase® G2, Ivoclar Vivadent) was pre-characterized and used with a radiant exposure of 24 J/cm2. The degree of conversion was evaluated by Raman spectrometry, and the elution of the monomers by nuclear magnetic resonance analysis (n=3). Data were analyzed using ANOVA and Tukey's test (α=0.05; β=0.2). Results: The combination of CQ and TPO increased the consumption of the photoinitiator system compared to CQ-only (p=0.001), but presented similar consumption compared to TPO-only (p=0.52). There was no significant difference in the degree of conversion between the composites regardless of the photoinitiator system (p=0.81). However, the elution of the monomers was reduced when both photoinitiators were combined. TPO-based material presented the highest elution of monomers. Conclusions: The combination of the photoinitiator systems seems to be beneficial for the cure efficiency of dental resin-based composites.

Polywave And Monowave Light-Curing Units Effects On Polymerization Efficiency Of Different Photoinitiators / Efeito Da Unidade De Cura Por Luz Polywave E Monowave Na Eficiência De Polimerização De Diferentes Fotoiniciadores

Objective: The objective of this study was to characterize and correlate the absorption spectra of three photoinitiators [camphorquinone (CQ), diphenyl(2,4,6-trimethylbenzoyl) phosphine oxide (TPO) and phenylbis (2,4,6-trimethylbenzoyl)-phosphine oxide (BAPO)], using second or third-generation light curing units (LCU), and to evaluate the degree of conversion and the physical properties of an experimental resin adhesive. Material and methods: Second-generation (Radii-cal® and Emitter D®) and third-generation (Valo® Cordless and Bluephase N®) LCU were assessed regarding spectrum and irradiance rate of emitted light. Also, the photoinitiators (CQ, TPO and BAPO) were characterized by a light absorption spectrum assessed by UV-Vis spectroscopy, degree of conversion and yellowing effect. Statistical analyzes considered two-way ANOVA and post-hoc Tukey test. Results: BAPO presented higher reactivity compared to TPO. Regarding degree of conversion of the photoinitiators activated by different light-curing units, the Emitter D® device promoted a high degree of conversion. BAPO presented the highest yellowing effect values. Conclusions: The emission and absorption characteristics of the photoinitiators were different. The polymerization reaction activated by the second-generation light-curing unit was reduced when using an experimental resin with photoinitiator TPO, and the third-generation light-curing unit showed a higher polymerization potential regardless of the photoinitiator. (AU)

Objetivo: Caracterizar e correlacionar os espectros de absorção de três fotoiniciadores [canforoquinona (CQ), difenil 2,4,6-trimetilbenzil óxido de fosfina (TPO) e óxido de di (2,4,6-trimetilbenzil) difenil fosfina (BAPO)], com unidades de fotoativação (LCU) de segunda ou terceira geração, e avaliar o grau de conversão e as propriedades físicas de um adesivo experimental. Material e métodos: LCU de segunda geração (Radii-cal® e Emitter D®) e terceira geração (Valo® Cordless e Bluephase N®) foram avaliadas quanto ao espectro e taxa de irradiância da luz emitida. Além disso, os fotoiniciadores (CQ, TPO e BAPO) foram caracterizados por um espectro de absorção de luz avaliado por espectroscopia UV-Vis, avaliado o grau de conversão dos adesivos e efeito de amarelamento. A análise estatística empregada foi ANOVA duas vias e teste post-hoc de Tukey. Resultados: BAPO apresentou maior reatividade comparado ao TPO. Em relação ao grau de conversão dos fotoiniciadores ativados por diferentes aparelhos fotopolimerizadores, o dispositivo Emitter D® promoveu um alto grau de conversão. BAPO apresentou os maiores valores de efeito de amarelamento. Conclusões: As características de emissão e absorção dos fotoiniciadores foram diferentes. A reação de polimerização ativada pelas unidades de fotopolimerização de segunda geração foi reduzida com o uso de uma resina experimental com fotoiniciador TPO. As unidades de fotopolimerização de terceira geração apresentaram maior potencial de polimerização independentemente do fotoiniciador. (AU)

Influence of different types of light curing units and photoinitiators in microhardness and color of composite resins after immersion in wine / Influencia dos diferentes tipos de unidade fotoativadoras e fotoiniciadores na microdureza e cor de resinas compostas após imersão em vinho

Objective: the aim of this study is to evaluate the microhardness and color change (∆E) of composite resins, that were light-cured with different LEDs, after being immersed in a staining drink. Material and Methods: Two composite resins with Lucerin-TPO (Tetric N-Ceram/ Vit-l-escence) and camphorquinone (Filtek Z350) were selected. The specimens (n=120) were prepared and lightcured with LED of monowave or polywave lightemitting diode (LED) devices. Microhardness and color evaluations were measured before and after immersion in staining drink. Microhardness data were evaluated by Kruskal-Wallis test, MannWhitney and Wilcoxon tests. Color changes were evaluated by two-way analysis of variance (ANOVA) and Tukey test (p ≤ 0.05). Results: No statistically significant difference between the two generations of LEDs was found for microhardness data. Regarding the ∆E, a statistical difference between the two LEDs was observed for Tetric NCeram and Filtek Z350. Conclusion: The compostion of composites appears to have more influence on analyses than the type of LEDs used. A decreased microhardness occurred to Vit-lescence for monowave and to Filtek Z350 for both LED devices. A clinically perceptible color change was observed for Tetric-N Ceram and Filtek Z350 when polywave LED were used. (AU)

Objetivo: o objetivo deste estudo foi aviliar a microdureza e alteração de cor (∆E) de resinas compostas, fotoativadas com diferentes LEDs, imergidas em bebidas pigmetadas. Material e métodos: Duas resinas compostas com Lucerina-TPO (Tetric N-Ceram/ VIt-l-essence) e canforoquinona (Filtek Z350) foram selecionadas. Os espécimes (n=120) foram preparados. Os mesmos foram fotopolimerizados com LED monowave ou polywave. Microdureza e cor foram avaliadas antes e após a imersão em bebidas pigmentadas. Os dados de microdureza foram avaliados pelos testes de Kruskal-Wallis, Mann-Whitney e Wilcoxon. As alterações de cor foram avaliadas por análise de variância a dois critérios (ANOVA) e Tukey (p ≤ 0,05). Resultados: Não foi encontrada diferença estatística entre as duas gerações de LEDs, para os dados da microdureza. Quanto ao ∆E, foi encontrada diferença estatisticamente significante entre os dois LEDs, sendo observadas na Tetric N-Ceram na FIltek Z350. Conclusão: A composição das resinas compostas parece ter mais influencia nas análises do que o tipo de LEDs. Uma redução na microdureza ocorreu para Vit-lescence para monowave e para Filtek Z350 para ambos os dispositivos LED. Uma mudança de cor clinicamente perceptível foi observada em Tetric-N Ceram para polywave e Filtek Z350 para ambos os dispositivos LED. (AU)

Effect of diphenyliodonium hexafluorphosphate in the yellowing and properties of experimental resin cements

Aim: The yellowing effect is undesirable and can occur in the dental restoration margins when light-cured resin cements containing camphorquinone as photoinitiator is used. This study aimed to evaluate the effect of diphenyliodonium hexafluorphosphate (DPI) in photoinitiator systems that contained different concentrations of camphorquinone (CQ) and dimethylamino ethyl benzoate (EDAB) on resin cements. Methods: A base (1:1) of bisphenol A diglycidyl methacrylate (BisGMA) and triethylene glycol dimethacrylate (TEGDMA) was obtained, and 60wt% of glass fillers was added. Eight formulations were obtained: RC1 (0.5mol% CQ / 1mol% EDAB), RC2 (0.5mol% CQ / 2mol% EDAB), RC3 (1mol% CQ / 1mol% EDAB), RC4 (1mol% CQ / 2mol% EDAB), and RC5 to RC8, which contained the same bases plus 0.5mol% DPI. Experimental resin cements were evaluated by the degree of conversion (DC), L*a*b* color analysis, water sorption (WS) and solubility (S), flexural strength, and Elastic Modulus. The data were analyzed by three-way ANOVA, Tukey's and Mann-Whitney tests (α = 0.05). Results: The combination of DPI and 0.5mol% CQ increased DC in RC6 and L* in RC5 without increasing the WS and a* b* values. CQ at 1mol% showed higher values of b* and lower values of a*, except for RC3. Groups with 2mol% EDAB showed higher DC. Conclusion: The addition of DPI reduces CQ, generating a decreased yellowing effect, while maintaining adequate properties in the resin cements, especially with 2mol% EDAB

Light curing resin cements containing iodonium salts promote suitable apical bonding of posts to radicular dentin

Abstract The aim of this study was to analyze the efficiency of experimental light-curing resin cements (ERCs) with a ternary photo-initiator system containing diphenyliodonium hexafluorphosphate (DPI) and different amines on retention of glass-fiber posts to dentin (GFP). ERCs formulations: a 1:1 mass ratio of 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy)phenylpropane and triethyleneglycol dimethacrylate. Camphorquinone was used as initiator. Six experimental groups were established according to the amine used: [ethyl-4-(dimethylamino)benzoate-EDMAB or 2-(dimethylamino)ethyl methacrylate-DMAEMA] and the concentration of DPI (0, 0.5 mol%, 1 mol%). The resin cements Variolink II (dual- and light-cured versions) were used as commercial reference. Eighty recently extracted bovine incisors (n = 10) were selected for this study. The roots were prepared and the fiber posts were cemented with the resin cement specified for each experimental group. Specimens from coronal, middle, and apical thirds of the root were subjected to push-out bond strength test 24 hours after bonding. Data were subjected to split-plot ANOVA and the Tukey test (p = 0.05). ERCs containing DPI showed statistically significant higher bond strengths compared with ERCs without DPI. ERCs containing DPI were statistically similar to VARIOLINK II - dual-cured and superior to VARIOLINK II - light-cured (except for EDMAB - 1DPI in the medium third and DMAEMA - 1DPI in the coronal third). Different amines did not influence post retention. The apical root region showed the lowest bond strength for the groups EDAB-0DPI, DMAEMA-0DPI and VARIOLINK II light-cured. Light-cured ERCs containing DPI were efficient for GFP retention to radicular dentin, with similar behaviour to that of dual-curing commercial resin cement.

Light curing in dentistry and clinical implications: a literature review

Abstract Contemporary dentistry literally cannot be performed without use of resin-based restorative materials. With the success of bonding resin materials to tooth structures, an even wider scope of clinical applications has arisen for these lines of products. Understanding of the basic events occurring in any dental polymerization mechanism, regardless of the mode of activating the process, will allow clinicians to both better appreciate the tremendous improvements that have been made over the years, and will also provide valuable information on differences among strategies manufacturers use to optimize product performance, as well as factors under the control of the clinician, whereby they can influence the long-term outcome of their restorative procedures.

Effects of radiant exposure values using second and third generation light curing units on the degree of conversion of a lucirin-based resin composite

Abstract Alternative photoinitiators with different absorption wavelengths have been used in resin composites (RCs), so it is crucial to evaluate the effectiveness of light-curing units (LCUs) on these products. Objective Using Fourier transform infrared analysis (FTIR) in vitro, the effects of varying radiant exposure (RE) values generated by second and third generation LED LCUs on the degree of conversion (DC) and maximum rate of polymerization (Rpmax) of an experimental Lucirin TPO-based RC were evaluated. Material and Methods 1 mm or 2 mm thick silicon molds were positioned on a horizontal attenuated total reflectance (ATR) unit attached to an infrared spectroscope. The RC was inserted into the molds and exposed to varying REs (18, 36 and 56 J/cm2) using second (Radii Plus, SDI) and third generation LED LCUs (Bluephase G2/Ivoclar Vivadent) or a quartz tungsten based LCU (Optilux 501/SDS Kerr). FTIR spectra (n=7) were recorded for 10 min (1 spectrum/s, 16 scans/spectrum, resolution 4 cm-1) immediately after their application to the ATR. The DC was calculated using standard techniques for observing changes in aliphatic to aromatic peak ratios both prior to, and 10 min after curing, as well as during each 1 second interval. DC and Rpmax data were analyzed using 3-way ANOVA and Tukey’s post-hoc test (p=0.05). Results No significant difference in DC or Rpmax was observed between the 1 mm or 2 mm thick specimens when RE values were delivered by Optilux 501 or when the 1 mm thick composites were exposed to light emitted by Bluephase G2, which in turn promoted a lower DC when 18 J/cm2 (13 s) were delivered to the 2 mm thick specimens. Radii Plus promoted DC and Rpmax values close to zero under most conditions, while the delivery of 56 J/cm2 (40 s) resulted in low DC values. Conclusions The third generation LCU provided an optimal polymerization of Lucirin TPO-based RC under most tested conditions, whereas the second generation LED-curing unit was useless regardless of the RE.

Influence of Different Photoinitiators on Polymerization Kinetics and Marginal Microleakage in Restorations using Photopolymerizable Dental Composites

Objective: To evaluate the influence of four different photoinitiators on the polymerization kinetics and marginal microleakage in class V restorations using photopolymerizable dental composites. Material and Methods: Four photopolymerizable dental composites based on Bis-GMA (14.5 wt %), UDMA (6.5 wt %) and silanized filler particles (79 wt %) containing different photoinitiators were formulated. Camphorquinone (CQ)/amine, phenyl-propanedione (PPD), monoacylphosphine oxide (Lucirin® TPO) and bisacylphosphine oxide (Irgacure® 819) were used as photoinitiators. Sixteen intact human third molars were selected and divided into four groups. All teeth received class V cavity preparations in their buccal and lingual surfaces and were submitted to a dye leakage test. Data were independently analyzed for both enamel and dentin, and the results were assessed by a Kruskal-Walis test. The polymerization reactions of the four composites were evaluated by differential scanning calorimeter coupled with photocalorimeter accessory. Results: Lucirin® TPO presented the highest scores for microleakage in enamel, whereas the other photoinitiators have not demonstrated statistical differences. The lowest scores were obtained for PPD in dentin while the highest scores have been achieved by Irgacure® 819 and Lucirin® TPO. Photocalorimetric measurements demonstrated a correlation between polymerization reaction rate and marginal leakage, showing that faster reactions cause greater marginal leakage. Conclusion: Marginal microleakage scores in photopolymerizable dental composites can be greatly influenced by different types of photoinitiators through their distinct reaction rates.

Técnicas para reduzir os efeitos da contração de polimerização das resinas compostas fotoativadas / Techniques for reducing the effects of polymerization shrinkage of composites photoactivated resins

Introdução: uma complicação inerente a todas as resinas compostas é o stress gerado pela contração de polimerização. As resinas compostas da atualidade, após a polimerização, perdem entre 2% a 3% de todo o seu volume. Essa perda pode acarretar em alterações fortemente comprometedoras a nível micro e macroscópico. Objetivo: abordar a importância do uso de técnicas e manobras clínicas, que visam diminuir a contração de polimerização das resinas compostas, reduzindo seus efeitos na cavidade, para que se tenha um procedimento restaurador com elevado índice de sucesso clínico e boa aceitação pelos pacientes. Material e Métodos: foi realizada uma revisão da literatura por meio de uma busca bibliográfica nas seguintes bases de pesquisa online: PUBMED/MEDLINE, LILACS, BBO e SCIENCE DIRECT, através do rastreio de artigos relevantes publicados entre o período de 2000 a 2015. Resultados: comparando as formas de ativação dos compósitos, os compósitos fotopolimerizáveis possuem um menor escoamento e maior stress de contração se comparados a compósitos com ativação química, isso se dá devido à fotoativação que se destaca por ser uma reação rápida quando comparada a outros métodos, não dispondo de tempo para a resina se acomodar na cavidade e ter uma boa interação com o sistema adesivo previamente aplicado, levando a grande parte dos problemas clínicos das restaurações. Conclusão: questionamentos sobre os efeitos da contração de polimerização, ainda não foram completamente elucidados no meio científico, por isso algumas técnicas como a escolha de fotopolimerizadores a LED, manutenção da fase pré gel, manutenção do Fator C e técnica de inserção incremental, podem ser usadas para minimizar os efeitos dessa contração nas restaurações feitas com resina, afim de reduzir insucessos como, sensibilidade pós operatória, infiltração marginal e riscos de agressão pulpar levando a uma maior longevidade dos procedimentos restauradores com materiais resinosos. (AU)

Introduction: a complication inherent in all composite resins is the stress generated by the polymerization contraction. The present composite resins, after polymerization, lose between 2% and 3% of their entire volume. This loss can lead to strongly compromising micro and macroscopic changes. Objective: to address the importance of using technical and clinical maneuvers, which aim to reduce polymerization shrinkage of composite resins, reducing its effects in the cavity, in order to have a restorative procedure with high clinical success rate and good patient acceptance. Material and Methods: a review of the literature through a literature search in the following search online databases was performed: PubMed/MEDLINE, LILACS, BBO and SCIENCE DIRECT, through the screening of relevant articles published between 2000 to 2015. Results: comparing both activation of composites, the dental composites have a lower flow and higher stress of contraction compared to composites with chemical activation, this is the due to photoactivation that stands out for being a quick reaction when compared to other methods, not providing time for the resin to settle in well and have a good interaction with the previously applied adhesive system, leading to much of the clinical problems of restorations. Conclusion: questions about the effects of polymerization shrinkage have not been fully elucidated in the scientific community, so some techniques such as the choice of curing lights to LED, the pre gel phase maintenance, maintenance of Factor C and incremental insertion technique can It is used to minimize the effects of this contraction in restorations made with resin in order to reduce failures as post-operative sensitivity, microleakage and pulp assault risks leading to increased longevity of restorative procedures with resinous materials. (AU)

Evaluation of phenyl-propanedione on yellowing and chemical-mechanical properties of experimental dental resin-based materials

ABSTRACT Objective To evaluate the influence of phenyl-propanedione on yellowing and chemical-mechanical properties of experimental resin-based materials photoactivated using different light curing units (LCUs). Material and Methods Experimental resin-based materials with the same organic matrix (60:40 wt% BisGMA:TEGDMA) were mechanically blended using a centrifugal mixing device. To this blend, different photoinitiator systems were added in equimolar concentrations with aliphatic amine doubled by wt%: 0.4 wt% CQ; 0.38 wt% PPD; or 0.2 wt% CQ and 0.19 wt% PPD. The degree of conversion (DC), flexural strength (FS), Young’s modulus (YM), Knoop hardness (KNH), crosslinking density (CLD), and yellowing (Y) were evaluated (n=10). All samples were light cured with the following LCUs: a halogen lamp (XL 2500), a monowave LED (Radii), or a polywave LED (Valo) with 16 J/cm2. The results were analysed by two-way ANOVA and Tukey’s test (α=0.05). Results No statistical differences were found between the different photoinitiator systems to KNH, CLS, FS, and YM properties (p≥0.05). PPD/CQ association showed the higher DC values compared with CQ and PPD isolated systems when photoactivated by a polywave LED (p≤0.05). Y values were highest for the CQ compared with the PPD systems (p≤0.05). Conclusion PPD isolated system promoted similar chemical and mechanical properties and less yellowing compared with the CQ isolated system, regardless of the LCU used.

Influência dos sistemas fotoiniciadores sobre as propriedades físicas e mecânicas de cimentos resinosos fotoativados por diferentes fontes de luz / Effect of light curing units on the physical and mechanical properties of lutting resin cements containing different photoinitiators systems

A utilização de sistemas iniciadores alternativos na composição de cimentos resinosos fotoativados tem por objetivo melhorar as propriedades químicas, mecânicas e estéticas dos agentes de cimentação odontológicos, reduzindo os aspectos desfavoráveis do sistema iniciador convencional, canforoquinona/amina. Para isso, um correto relacionamento entre o espectro de emissão da fonte de luz e o espectro de absorção do fotoiniciador é fundamental. O presente estudo tem como objetivo, através de uma revisão de literatura, avaliar as possíveis alterações físicas e mecânicas atribuídas a agentes de cimentação resinosos fotoativados, contendo diferentes sistemas fotoiniciadores sob efeito de diferentes tipos de fonte de luz...

The use of alternative initiator systems in the composition of luting resin cements aims to improve chemical, mechanical, and aesthetic properties of dental cementation agents, reducing the drawbacks aspects of the conventional initiator system, canphorquinone/amine. Therefore the proper interaction between the light-curing units emission spectrum and the photo-initiator absorption spectrum is r. This study presents a literature review with the objective of evaluating the possible physical and mechanical changes on photoactivated resin cements, containing different photo-iniciators systems under the effect of different types of light sources...

Effect of the photoinitiator system on the properties of a dental material based on a hybrid polymer / Efeito do sistema fotoiniciador sobre as propriedades de um material dentário baseado em um polímero híbrido

Objetivo: Nesse estudo, foram avaliados os efeitos de dois diferentes protocolos de cura sobre as propriedades de um compósito usando um polímero híbrido como resina dentária. Material e Métodos: Dois compósitos diferentes foram preparados, um contendo uma mistura de TEGDMA/Bis-GMA (50:50) e, outro contendo uma mistura de TEGDMA/p-MEMO (50:50), [p-MEMO: precursor oligomérico inorgânico]. Ambos compósitos foram reticulados com lucirin e canforoquinona. Os compósitos foram preparados com 70% em massa de carga inorgânica. Resistência flexural foi avaliada com uma máquina de testes universal e o grau de conversão calculado por espectroscopia na região do infravermelho. Um picnômetro a gás hélio foi usado para obter os dados de contração de polimerização. Testes de sorção foram feitos e microscopia eletrônica de varredura foi usada para avaliar efeitos deletérios sobre as superfícies das resinas. Resultados: A amostra constituída com TEGDMA/p-MEMO reticulada com lucirin (L-T/p) apresentou os melhores valores das propriedades monitoradas. Conclusão: Lucirin é o sistema fotoiniciador mais adequado para compostos dentários contendo polímeros híbridos.

Objective: In this study, the effects of two different cure protocols upon the properties of composites using a hybrid-polymer as dental resin were evaluated. Material and Methods: Two distinct dental composites were prepared, one containing a mixture of TEGDMA/bis-GMA (50:50) and, another containing a mixture of TEGDMA/p MEMO (50:50), [p-MEMO: oligomeric inorganic precursor]. Both composites were polymerized with lucirin and canphorquinone as photoinitiators. The composites were made with a 70 % wt of inorganic filler. Flexural strength was evaluated with a universal test machine and the degree of conversion was measured by infrared spectroscopy. A helium pycnometer was used to obtain polymer shrinkage data. Sorption tests were performed and SEM microscopy was used to show deleterious effects upon the resins’ surfaces. Results: The sample based on TEGDMA/p-MEMO polymerized with lucirin (L-T/p) showed the best values of the monitored properties. Conclusion: Lucirin is the most suitable photoinitiator for dental composites containing hybrid polymers.

Influence of polymeric matrix on the physical and chemical properties of experimental composites

Nowadays, the main reasons for replacement of resin-based composite restorations are fracture or problems with the integrity of their interface, such as marginal staining, microleakage, or secondary caries. The aim of the present study was to evaluate the influence of the organic matrix on polymerization stress (PS), degree of conversion (DC), elastic modulus (E), flexural strength (FS), Knoop hardness (KHN), sorption (SP), and solubility (SL). In order to obtain a material which combines better mechanical properties with lower PS, seven experimental composites were prepared using BisGMA to TEGDMA molar ratios of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2 and 40% of silica. PS was obtained in a universal testing machine, using acrylic as bonding substrate. DC was determined using Fourier Transform Raman spectroscopy. E and FS were obtained by the three-point bending test. KHN was measured by a microindentation test using a load of 25 g for 30 s. SP and SL were assessed according to ISO 4049. The data were submitted to one-way ANOVA. The increase in BisGMA concentration resulted in the decrease of PS, DC, E, FS and KHN. However, it did not change the SP and SL values. FS, E and KHN showed a strong and direct relationship with the DC of the materials. The composite material with a BisGMA to TEGDMA molar ratio of 1:1 was the one with better mechanical properties and lower PS.

Influence of photoinitiators and light sources on the degree of conversion of experimental resin cements / Influência de fotoiniciadores e fontes de luz no grau de conversão de cimentos resinosos experimentais

Objetivo: O objetivo deste estudo foi avaliar o grau de conversão (DC) de sete cimentos resinosos experimentais formulados com diferentes fotoiniciadores, quando ativados por duas fontes luminosas (LCUs) atravessando a cerâmica. Material e Métodos: Sete formulações foram preparadas com diferentes concentrações (em peso) de Canforoquinona (CQ) e/ou Fenilpropanodiona (PPD): C5: 0,5% CQ; C8: 0,8% CQ; P5: 0,5% PPD; P8: 0,8% PPD; C1P4: 0,1% CQ e 0,4% PPD; C4P1: 0,4% CQ e 0,1% PPD; e C4P4: 0,4% CQ e 0,4% PPD. Cada mistura foi carregada com 65% em peso de partículas de carga silanizada. Foram usadas duas fontes luminosas para a fotoativação: uma de luz halógena de quartzo-tungstênio (QTH) e uma de diodo emissor de luz (LED). A irradiância (mW/cm²) foi calculada pela potência média de saída dividida pela área da ponta do aparelho. DC foi obtido por espectroscopia de infravermelho transformada de Fourier. Os dados foram submetidos a ANOVA 2-Fatores e ao teste de Tukey (5%). Resultados: Os valores de DC não exibiram diferenças significativas para LCUs, independente do tipo de fotoiniciador. O maior DC foi observado para o cimento P8, e o menor para C5. Valores intermediários de DC foram observados nos demais cimentos. No entanto, quando usado QTH, P8 diferiu dos cimentos C1P4, C4P1 e C5; e quando o LED foi empregado, P8 diferiu apenas de C4P1 e C5. Conclusão: Portanto, PPD é uma alternativa viável para o desenvolvimento de cimentos resinosos fotoativados, e a associação PPD/CQ também pode ser viável, uma vez que C4P4 foi semelhante a P8.

Objective: The aim of this study was to evaluate the degree of conversion (DC) ofseven experimentalresin cements formulated with different photoinitiators when activated by two light-curing units (LCUs) through ceramic material. Material and Methods: Seven resin blends with different camphorquinone (CQ) and/or phenyl propanedione (PPD) ratios were prepared: C5: 0.5% wt CQ; C8: 0.8% wt CQ; P5: 0.5% wt PPD; P8: 0.8% wt PPD; C1P4: 0.1% wt CQ and 0.4% wt PPD; C4P1: 0.4% wt CQ and 0.1% wt PPD; and C4P4: 0.4% wt CQ and 0.4% wt PPD. Each mixture was loaded with 65% wt of silanized filler particles. For photoactivation procedures, two LCUs were used: a quartz-tungsten-halogen (QTH) and a light emitting diode (LED). Irradiance (mW/ cm²) was calculated by the ratio of the output power by the area of the tip. DC was assessed by Fourier transformed infrared spectroscopy. Data were submitted to a two-way ANOVA and Tukey’s test (5%). Results: DC values do not show significant differences for LCUs regardless of the photoinitiator type. The highest DC was found for experimental cement P8 and the lowest for C5. Intermediate DC values were found for the other cements. However, when QTH was used, P8 exhibited differences among C1P4, C4P1 and C5; whereas when LED was used, P8 differed only for C4P1 and C5. Conclusion: Thus, PPD is a viable alternative for the manufacture of photoactivated cements, and the PPD/CQ association may also be viable since C4P4 was similar to P8.

Monomers used in resin composites: degree of conversion, mechanical properties and water sorption/solubility

The organic phase of resin composites is constituted by dimethacrylate resins, the most common monomers being the bisphenol A diglycidildimethacrylate (BisGMA), its ethoxylated version (BisEMA), triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA). This study compared the homopolymers formed from the monomers used in restorative dental composites in terms of their degree of conversion (DC) and reaction kinetics (by near infra-red spectroscopy, n=3), mechanical properties (flexural modulus and strength in three point-bending, FM and FS, respectively, n=15), water sorption and solubility (WS and SL, respectively - ISO 4049, n=5). Materials were made photopolymerizable by the addition of camphoroquinone/dimethylamine ethyl methacrylate. TEGDMA showed the highest DC, followed by BisEMA, UDMA and BisGMA, both at 10 min and at 24h (p<0.001). UDMA showed the highest rate of polymerization, followed by TEGDMA, BisEMA and BisGMA (H0=13.254, p<0.001). UDMA and TEGDMA presented similar FM, significantly higher (p<0.001) than BisEMA and BisGMA, which in turn present statistically similar values (p>0.001). For FS, UDMA presented the highest value (p<0.001), followed by TEGDMA, then by BisEMA and BisGMA, which were statistically similar (p>0.001). BisGMA showed the highest WS, and TEGDMA and BisEMA the lowest. UDMA was statistically similar to all (H0=16.074, p<0.001). TEGDMA presented the highest SL, followed by UDMA, BisGMA and BisEMA (p<0.001). The tested homopolymers presented different behaviors in terms of polymerization kinetics, flexural properties, water sorption and solubility. Therefore, the use of copolymers is justified in order to obtain high DC and mechanical properties, as well as good resistance to water degradation.

A fase orgânica de compósitos resinosos é constituída por dimetacrilatos, sendo os mais comuns o dimetacrilato de diglicidilabisfenol A (BisGMA), sua versão etoxilada (BisEMA), dimetacrilato de trietilenoglicol (TEGDMA) e dimetacrilato de uretano (UDMA). Este estudo comparou os homopolímeros formados pelos monômeros utilizados em compósitos restauradores dentários em relação a seus graus de conversão (GC) e cinética de reação (através de espectroscopia no infra-vermelho), propriedades mecânicas (módulo de elasticidade em flexão e resistência à flexão, MF e RF, respectivamente), sorção de água e solubilidade (SA e SL, respectivamente - ISO4049). Os materiais se tornaram fotopolimerizáveis pela adição de canforoquinona/metacrilato de dimetilaminoetila e foram fotoativados utilizando uma fonte de luz de quartzo-tungstênio-halogênio filtrada para 400-500 nm. O TEGDMA apresentou o maior GC, seguido pelo BisEMA, UDMA e BisGMA, tanto aos 10 min quanto após 24 h (p<0,001). O UDMA mostrou a maior velocidade de reação, seguido pelo TEGDMA, BisEMA e BisGMA (H0=13,254, p<0,001). O UDMA e o TEGDMA apresentaram MF semelhantes, estatisticamente superiores ao BisEMA e ao BisGMA (p<0,001), os quais por sua vez apresentaram valores estatisticamente semelhantes (p>0,001). Para RF, o UDMA apresentou o valor mais alto, seguido pelo TEGDMA, BisEMA e BisGMA (p<0,001), sendo os dois últimos estatisticamente semelhantes (p>0,001). O BisGMA apresentou a maior SA, e o TEGDMA e o BisEMA as menores. O UDMA foi estatisticamente semelhante a todos (H0=16,074, p<0,001). O TEGDMA apresentou a maior SL, seguido pelo UDMA, BisGMA e BisEMA (p<0,001). Os homopolímeros demonstraram desempenhos bastante distintos em relação à cinética de polimerização, propriedades em flexão e sorção e solubilidade. Tais diferenças justificam o uso de co-polímeros para a obtenção de materiais com propriedades físicas otimizadas.

Photoelastic evaluation of the effect of composite formulation on polymerization shrinkage stress

We compared polymerization stress in two commercial composites and three experimental composites made using camphorquinone (CQ) and/or phenylpropanedione (PPD) as photoinitiators. The internal surfaces of photoelastic resin discs with cylindrical cavities were roughened and treated with adhesive. Composites were divided into five groups: two commercial composites (Filtek Silorane and Filtek Z250) and three experimental composites with CQ/amine, CQ/PPD/amine, and PPD/amine. Composites were photopolymerized inside cavities, and subjected to photoelastic analysis immediately and at 24 hours and 7 days later using a plane polariscope. Stress created by Silorane (3.08 ± 0.09 MPa) was similar to that of Z250 (3.19 ± 0.13 MPa) immediately after photopolymerization (p > 0.05). After 24 hours and 7 days, Z250 (3.53 ± 0.15 and 3.69 ± 0.10 MPa, respectively) showed higher stress than Silorane (3.19 ± 0.10 and 3.16 ± 0.10 MPa, respectively). Qualitative analysis immediately after photopolymerization showed composite/CQ promoted higher stress than PPD, but stress levels at other evaluated times were statistically similar, varying between 3.45 ± 0.11 MPa and 3.92 ± 0.13 MPa. At 24 hours and 7 days, Silorane created the lowest stress. All photoinitiators created comparable tensions during polymerization.